Q&A

I'm new to using gels but I'm having trouble getting the nails just right.

Q.

I have been doing gels for about three weeks and I’m ready to give up and go back to acrylics. Some of my clients’ nails are a mess after two weeks. I hate having to deal with the forms and it takes a lot longer because I have to put on so many layers, curing each one and then the underside. Any advice?

A.

I have been doing gels for about three weeks and I’m ready to give up and go back to acrylics. Some of my clients’ nails are a mess after two weeks. I hate having to deal with the forms and it takes a lot longer because I have to put on so many layers, curing each one and then the underside. Any advice?

Lin Halpern: Because gels are light-cured, the lamp’s light must penetrate through the gel to cure it. Colored gels will not let light pass through them, making layering the only way to get them to set. Avoid using these types at first. You can always check to see how they work when you have time to play. Gels are not like acrylics – don’t apply your acrylic techniques to the gels. Begin by using tips, not forms. Tips provide the perfect platform on which to build a beautiful gel nail. Blend the seam properly and you won’t be able to tell your gel nails from a natural one. Shape and shorten before going to the gel application. Be sure the gel you choose is not too thin. Thinner gels run, so look for gels that “stand up” or do not slump quickly. They are easier to handle.

Use the “house” building method. Once the nail surface is prepared according to the manufacturer’s instructions, begin with the bonder or base coat gel. Pretend you are polishing the surface with red nail polish. Do not touch the sidewalls or cuticle area and be sure to wrap around the free edge thickness. Cure in the UV lamp. This is the foundation of your house.

Next, build your walls. Take the builder gel and drag a line from cuticle to free edge like a speed bump you find in a parking lot. Place it directly down the middle starting slightly below the cuticle as not to touch the skin. The base coat is still tacky and will grab the gel off your brush. Just get close and barely touch the gel from the brush to the tacky, cured surface and drag down to the tip. Cure in the UV lamp for 20 seconds. This will freeze the action just enough to put another layer on immediately without disturbing the first builder layer. Now, apply the second layer of the builder just like you did the base coat covering the entire surface and wrapping the edge. Cure for the full time required. When the cure is complete, wipe the nail surface to remove the sticky film layer. If your lamp has a reflective floor there should be no need to turn the hands upside down.

Now, feel the nail. Adjust the surface contour with a 180-grit file – a harsher grit will remove too much. A block buffer will do for most of the surface. When using the 180-grit file be careful not to stroke the extended sidewall and free edge with too heavy a hand as this may remove the gel bond from the tip. Just crisp up your original shape and flatten out the U-shaped cuticle area.

The last step of building your strong house is your roof or top coat. Clean the nail of all dust and apply the top coat. Keep away from the skin and wrap all the edges. Finish curing and wiping according to the directions. If the gel is cured by the correct lamp for your gel and your bulbs are strong and not used up, the bond should stay perfect until the client returns for the refill. With no lifting and therefore no nipping, the refill is just a small area to fill and the free edge requires shortening and re-sealing.

LaCinda Headings: Any time you try a new system, there is going to be an adjustment time. Gels are a great alternative service for your clients who are prone to lifting or allergic to acrylic. Plus they are great for spa atmospheres because they have no harsh odor. Doing a set of gels takes about the same amount of time as doing a set of acrylics once you get used to the different systems. Sculpting gels can be challenging – look for a system where the sculpting gel is thick enough that you can do more than one nail at a time and doesn’t have to be cured underneath as well. If the gels aren’t holding up the way that they should, call the manufacturer to find out what’s going wrong.

 

Leave a Comment

Name:
Email:
Comment:
Submit

Comments (0)

Encyclopedia

Microscopic plants such as mold, dermatophyte, and yeast; only two members of this family can form colonies in or under the natural nail and under...
Learn More

Subscribe to NAILS & SAVE!

Get a free preview issue and a Free Gift
Subscribe Today!

Please sign in or register to .    Close
Loading...
 
Subscribe Today
Subscribe Today