Nails
MenuMENU
SearchSEARCH

Technique

I have a client with fan-shaped nails that are also very flat.

March 1, 2003

irst, know that these are the most difficult type of nails to work with. So is she lifting? Cracking? Coming off? If she lifts at the cuticle, proper nail prep is a must. Make sure the cuticles are pushed back and the entire nail — especially around the cuticle edge — is well etched. If she is lifting from the free edge, you must remove the lifted area and replace it with new acrylic. Don’t try to make the nail follow the shape of the acrylic. Acrylic will grow straight out with very little flexing, but the natural nail will twist and turn (and dip down and up) especially once it leaves the nail bed.

If the nails are coming off, make sure there is no dust left on them and a bonding agent is used before applying the tip and before applying the primer. Next, I would suggest using a full well tip and a gel glue to accommodate the flat nail, making sure there are no air pockets under the tip. Also make sure the tip is as wide as the nail’s free edge. Concentrate your tip, blending to the center of the well that overlaps the nail (leaving the area closest to the cuticle the thickest). This enables the C-curve of the tip well to “flex” to the nail instead of squeezing its way off the nail bed. I’m a big advocate of acid-less primers, but in this situation I’d use an acid primer. It is especially important to make the free edge no more than half the length of the nail bed. The longer the free edge, the more pressure the stress area will take on. When applying the acrylic, having a good arch is important for added strength.

If the nail is cracking in the stress area, cut into the acrylic where it is cracked to allow the acrylic to get into the crack instead of just laying on it. Also when filling in, add a ball to each side of the nail (parallel to the cuticle) sweeping it toward the center of the nail. — Angie Gross is a nail tech at Soge Hair and Body Care in Atlanta


You have not said if you are using tips or sculpting, but I would assume that you are using tips. Try to sculpt her nails and see if you find a difference. You may also want to keep her natural nails under the enhancement shorter by using your electric file or a round file under the nails. You cannot force or change the shape of these nails. Her nails are most likely pulling away from the product and lifting. Keeping her nails shorter and preventing them from growing out might help you.— Lynnette Madden is owner of Salon 29 at Main in East Greenville, Pa.



More FAQ

Why is it that most of my acrylic clients are having lifting by the cuticle area?

Why is it that most of my acrylic clients are having lifting by the cuticle area? I prep properly, removing all the oils from the nail beds, and I prime twice. I’ve even considered using an 80-grit file. What can I do or what am I doing wrong?... read more

My clear and acrylic nails appear dull or frosted. What am I doing wrong?

After I apply clear or natural acrylic nails, they don’t appear clear. They have an almost frosted or dull look. What am I doing wrong? Am I applying too much?... read more

How to I keep wraps from lifting on a client with poor circulation?

I have a client with very poor circulation, and therefore, very cold hands, making it difficult to keep her silk overlays from lifting. I have already tried pH balancers and extra silk and resin, but the lifting continues to occur. What else could I try that might work?... read more

If I don't etch the nails before applying acrylics, do I need to apply more primer?

During my training for fills, I was taught to etch the natural nail regrowth for the strongest hold and to prevent lifting. Yet, I recently read that a technician did not etch the nail because it causes so much damage. I agree, but wonder what the major difference would be without etching? Should I apply more primer?... read more

Should I remove the gel overlay from my client's damaged nail?

I have a client who wears gels over her natural nails. She hit her nail really hard and although it didn’t come off, it did bleed underneath the nail plate. Should I remove the overlay from the nail? Should I be worried about infection setting in?... read more

Is it common to have to change products or procedures depending on the weather?

Is it common to have to change products or procedures (including changing the ration of the products) depending on the weather? Is it possible for perspiration to make the product lift?... read more

Can you over-cure gel?

Can you over-cure gel?... read more

Why do some of my clients feel a burning sensation when I use my e-file?

I have only had my license for six months, and I have definitely found that my e-file cuts down on time. The only problem is when I’m reducing the acrylic to take off old product, some of my clients feel a burning sensation. I make sure I’m not applying too much pressure. I have my RPM set at 15,000 and usually use a medium-grit sanding band. What can I do about this? Should I go back to carbide bits?... read more

Why do some people wear gels over acrylic extensions?

I’ve heard that some people wear gels over acrylic extensions. Why do they do this, and how do you do this? Is there anything you have to be careful of during the application?... read more

I’ve heard that some people wear gels over acrylic extensions? Why do they do this, and how do you do this?

I’ve heard that some people wear gels over acrylic extensions? Why do they do this, and how do you do this? Is there anything you have to be careful of during the application?... read more

When I’m reducing the acrylic to take off old product, some of my clients feel a burning sensation. What can I do about this?

I have only had my license for six months, and I have definitely found that my e-file cuts down on time. The only problem is when I’m reducing the acrylic to take off old product, some of my clients feel a burning sensation. I make sure I’m not applying too much pressure. I have my RPM set at 15,000 and usually use a medium-grit sanding band. What can I do about this? Should I go back to carbide bits?... read more

Myth Busters: Will suntan lotion mixed with the ocean's salty water turn gels to goo?

I heard that if you go into the ocean with a lot of suntan lotion on, the small amount of acetone in the suntan lotion interacts with the salt water and can run down your fingers and turn your gels to goo. Is this true?... read more